Universidade Federal de Santa Catarina (UFSC), Departamento de Química, 88040-900 Florianópolis, SC, Brazil.
Anal Methods. 2022 Mar 31;14(13):1371-1377. doi: 10.1039/d1ay02048j.
Particulate matter (PM) impregnated with methlymercury (MeHg) was analyzed using atomic absorption spectrometry coupled to a customized dielectric barrier discharge (DBD) device. Chemical vapor generation (CVG) was applied to generate methylmercury hydride and the DBD device promoted bond cleavage with subsequent release of free Hg atoms to the gas phase. Hydride generation was carried out using a lab-made syringe-based device in batch mode using argon as a carrier gas. Optimized conditions included the use of 1.0 mL of a 0.05% m/v NaBH solution and 1.0 mL of a 10% v/v HCl solution. This system was coupled to the DBD device, designed to operate in "plasma jet" configuration. Assessment of the designed device for methylmercury detection was established based on an on-off switch, which promptly demonstrated that Hg signals could only be detected upon activation of the plasma discharge. In parallel, adsorption of MeHg to PM-loaded glass fiber filters was investigated. Direct analysis of methylmercury-impregnated PM resulted in significant signal suppression compared to the same mass of analyte from an aqueous standard, which suggests that methylmercury is efficiently adsorbed on PM. This was later confirmed by repeating the same experiment with "blank" (PM-free) glass fiber filters. Hence, extraction of methylmercury to a liquid phase was required for quantification. In order to demonstrate the feasibility of the proposed setup to carry out methylmercury detection in the presence oh Hg, recovery tests were conducted by mixing MeHg with Hg at three distinct concentration levels (100 : 1, 10 : 1 and 1 : 1 MeHg : Hg). Recoveries better than 91% were obtained for MeHg under these conditions, which demonstrates that the device is efficient for MeHg determination by simply modulating the plasma (switching on-off). Limits of detection and quantification were established as 6 ng and 19 ng, respectively.
用原子吸收光谱法结合定制的介质阻挡放电(DBD)装置分析了负载有甲基汞(MeHg)的颗粒物(PM)。化学蒸气发生(CVG)用于生成甲基汞氢化物,DBD 装置促进键的断裂,随后将游离汞原子释放到气相中。采用实验室自制的基于注射器的设备,在批处理模式下使用氩气作为载气进行氢化物发生。优化条件包括使用 0.05% m/v 的 NaBH 溶液 1.0 毫升和 10% v/v 的 HCl 溶液 1.0 毫升。该系统与 DBD 装置耦合,设计用于“等离子体射流”配置。根据开/关开关评估设计用于甲基汞检测的设备,该开关立即证明仅在等离子体放电激活时才能检测到 Hg 信号。同时,还研究了 MeHg 对负载有 PM 的玻璃纤维过滤器的吸附。与来自水溶液标准品的相同质量的分析物相比,直接分析负载有甲基汞的 PM 会导致信号明显抑制,这表明甲基汞被有效地吸附在 PM 上。这后来通过重复相同的实验(使用无 PM 的玻璃纤维过滤器)得到了证实。因此,需要将甲基汞提取到液相中进行定量。为了证明在存在 Hg 的情况下提出的设置进行甲基汞检测的可行性,通过将 MeHg 与 Hg 以三个不同的浓度水平(100:1、10:1 和 1:1 MeHg:Hg)混合进行回收测试。在这些条件下,MeHg 的回收率超过 91%,这表明该装置通过简单地调节等离子体(开关开/关)就能有效地用于 MeHg 的测定。检测限和定量限分别设定为 6 ng 和 19 ng。