Department of Chemistry, Fudan University, 200433 Shanghai, People's Republic of China.
Methods Appl Fluoresc. 2018 Apr 27;6(3):034002. doi: 10.1088/2050-6120/aab930.
Cyanine dyes are widely used in biological labeling and imaging because of their narrow near infrared emission, good brightness and high flexibility in functionalization, which not only enables multiplex analysis and multi-color imaging, but also greatly reduces autofluorescence from biological matter and increases signal-to-noise ratio. Unfortunately, their poor chemical- and photo-stability strongly limits their applications. The incorporation of cyanine dyes in silica nanoparticles provides a solution to the problem. On one hand, the incorporation of cyanine dyes in silica matrix can enhance their chemical- and photo-stability and increase brightness of the nanomaterials. On the other hand, silica matrix provides an optimized condition to host the dye, which helps to maintain their fluorescent properties during application. In addition, the well-established silane technique provides numerous functionalities for diverse applications. However, commercially available cyanine dyes are not very stable at high alkaline conditions, which will gradually lose their fluorescence over time. Our results showed that cyanine dyes are very vulnerable in the reverse micelle system, in which they will lose their fluorescence in less than half an hour. The existence of surfactant could greatly promote degradation of cyanine dyes. Fluorescent silica nanoparticles cannot be obtained at the high alkaline condition with the existence of surfactant. In contrast, the cyanine dyes are relatively stable in Stöber media. Owing to the fast formation of silica particles in Stöber media, the exposure time of cyanine dye in alkaline solution was greatly reduced, and highly fluorescent particles with good morphology and size distribution could be obtained via Stöber approach. However, the increasing water content in the Stöber could reduce the stability of cyanine dyes, which should be avoided. This research here provides a clear guidance on how to successfully synthesize cyanine dye-doped silica nanoparticles with good morphology, size distribution, stability and brightness.
花菁染料由于其窄的近红外发射、良好的亮度和在功能化方面的高灵活性而被广泛应用于生物标记和成像,这不仅使多色分析和多色成像成为可能,而且大大降低了生物物质的自发荧光并提高了信噪比。不幸的是,它们较差的化学和光稳定性强烈限制了它们的应用。将花菁染料掺入二氧化硅纳米粒子中为解决这一问题提供了一种方法。一方面,将花菁染料掺入二氧化硅基质中可以增强其化学和光稳定性,并提高纳米材料的亮度。另一方面,二氧化硅基质为染料提供了一个优化的宿主条件,有助于在应用过程中保持其荧光性能。此外,成熟的硅烷技术为各种应用提供了众多功能。然而,商业上可获得的花菁染料在高碱性条件下不是很稳定,随着时间的推移,它们的荧光会逐渐丧失。我们的结果表明,花菁染料在反胶束体系中非常脆弱,在不到半小时的时间内它们就会失去荧光。表面活性剂的存在会极大地促进花菁染料的降解。在存在表面活性剂的高碱性条件下,无法获得荧光二氧化硅纳米粒子。相比之下,花菁染料在 Stöber 介质中相对稳定。由于在 Stöber 介质中二氧化硅颗粒的形成速度很快,花菁染料在碱性溶液中的暴露时间大大缩短,通过 Stöber 方法可以获得具有良好形态和尺寸分布的高荧光粒子。然而,Stöber 中含水量的增加会降低花菁染料的稳定性,应避免这种情况。本研究为成功合成具有良好形态、尺寸分布、稳定性和亮度的花菁染料掺杂二氧化硅纳米粒子提供了明确的指导。